/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once #include "env_validate.h" #define DEFAULT_MACHINE_NAME "3D Printer" #define BOARD_INFO_NAME "FYSETC Cheetah V2.0" #define BOARD_WEBSITE_URL "fysetc.com" // USB Flash Drive support //#define HAS_OTG_USB_HOST_SUPPORT // Ignore temp readings during development. //#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 #if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION) #define FLASH_EEPROM_EMULATION #define FLASH_EEPROM_LEVELING #define FLASH_SECTOR 1 #define FLASH_UNIT_SIZE 0x4000 // 16k #define FLASH_ADDRESS_START 0x8004000 #endif // // Z Probe // #if ENABLED(BLTOUCH) #error "You need to set jumper to 5v for Bltouch, then comment out this line to proceed." #define SERVO0_PIN PA0 #elif !defined(Z_MIN_PROBE_PIN) #define Z_MIN_PROBE_PIN PA0 #endif // // Limit Switches // #define X_STOP_PIN PB4 #define Y_STOP_PIN PC8 #define Z_STOP_PIN PB1 // // Filament runout // #define FIL_RUNOUT_PIN PB5 // // Steppers // #define X_STEP_PIN PC0 #define X_DIR_PIN PC1 #define X_ENABLE_PIN PA8 #define Y_STEP_PIN PC14 #define Y_DIR_PIN PC13 #define Y_ENABLE_PIN PC15 #define Z_STEP_PIN PB9 #define Z_DIR_PIN PB8 #define Z_ENABLE_PIN PC2 #define E0_STEP_PIN PB2 #define E0_DIR_PIN PA15 #define E0_ENABLE_PIN PD2 #if HAS_TMC_UART #define X_HARDWARE_SERIAL Serial2 #define Y_HARDWARE_SERIAL Serial2 #define Z_HARDWARE_SERIAL Serial2 #define E0_HARDWARE_SERIAL Serial2 // Default TMC slave addresses #ifndef X_SLAVE_ADDRESS #define X_SLAVE_ADDRESS 0 #endif #ifndef Y_SLAVE_ADDRESS #define Y_SLAVE_ADDRESS 2 #endif #ifndef Z_SLAVE_ADDRESS #define Z_SLAVE_ADDRESS 1 #endif #ifndef E0_SLAVE_ADDRESS #define E0_SLAVE_ADDRESS 3 #endif #endif // // Heaters / Fans // #define HEATER_0_PIN PC6 #define HEATER_BED_PIN PC7 #ifndef FAN_PIN #define FAN_PIN PA14 #endif #define FAN1_PIN PA13 #define FAN2_PIN PA1 // // Temperature Sensors // #define TEMP_BED_PIN PC5 // Analog Input #define TEMP_0_PIN PC4 // Analog Input // // Misc. Functions // #define SDSS PA4 #define SD_DETECT_PIN PC3 #ifndef RGB_LED_R_PIN #define RGB_LED_R_PIN PB0 #endif #ifndef RGB_LED_G_PIN #define RGB_LED_G_PIN PB7 #endif #ifndef RGB_LED_B_PIN #define RGB_LED_B_PIN PB6 #endif /** * ------ ------ * (SD_MISO) PA6 |10 9 | PA5 (SD_SCK) (BEEPER) PC9 |10 9 | PC12 (BTN_ENC) * (BTN_EN1) PC10 | 8 7 | PA4 (SD_SS) (LCD_EN) PB15 | 8 7 | PB12 (LCD_RS) * (BTN_EN2) PC11 6 5 | PA7 (SD_MOSI) (LCD_D4) PB13 6 5 | PB14 (LCD_D5) * (SD_DETECT) PC3 | 4 3 | RESET (LCD_D6) PB6 | 4 3 | PB7 (LCD_D7) * GND | 2 1 | 5V GND | 2 1 | 5V * ------ ------ * EXP2 EXP1 */ /** * ------ * 5V |10 9 | GND * (LCD_EN/MOSI) PB15 | 8 7 | PB12 (LCD_RS) * (LCD_D4/SCK) PB13 6 5 | PC11 (BTN_EN2) * (LCD_D5/MISO) PB14 | 4 3 | PC10 (BTN_EN1) * (BTN_ENC) PC12 | 2 1 | PC9 (BEEPER) * ------ * EXP3 */ #define EXP1_03_PIN PB7 #define EXP1_04_PIN PB6 #define EXP1_05_PIN PB14 #define EXP1_06_PIN PB13 #define EXP1_07_PIN PB12 #define EXP1_08_PIN PB15 #define EXP1_09_PIN PC12 #define EXP1_10_PIN PC9 #define EXP2_03_PIN -1 #define EXP2_04_PIN PC3 #define EXP2_05_PIN PA7 #define EXP2_06_PIN PC11 #define EXP2_07_PIN PA4 #define EXP2_08_PIN PC10 #define EXP2_09_PIN PA5 #define EXP2_10_PIN PA6 #if HAS_WIRED_LCD #define BEEPER_PIN EXP1_10_PIN #define BTN_ENC EXP1_09_PIN #if ENABLED(CR10_STOCKDISPLAY) #define LCD_PINS_RS EXP1_07_PIN #define BTN_EN1 EXP2_08_PIN #define BTN_EN2 EXP2_06_PIN #define LCD_PINS_ENABLE EXP1_08_PIN #define LCD_PINS_D4 EXP1_06_PIN #elif ENABLED(MKS_MINI_12864) #define DOGLCD_A0 EXP1_04_PIN #define DOGLCD_CS EXP1_05_PIN #define BTN_EN1 EXP2_08_PIN #define BTN_EN2 EXP2_06_PIN #else #define LCD_PINS_RS EXP1_07_PIN #define BTN_EN1 EXP2_06_PIN #define BTN_EN2 EXP2_08_PIN #define LCD_PINS_ENABLE EXP1_08_PIN #define LCD_PINS_D4 EXP1_06_PIN #if ENABLED(FYSETC_MINI_12864) #define DOGLCD_CS EXP1_08_PIN #define DOGLCD_A0 EXP1_07_PIN //#define LCD_BACKLIGHT_PIN -1 #define LCD_RESET_PIN EXP1_06_PIN // Must be high or open for LCD to operate normally. #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) #ifndef RGB_LED_R_PIN #define RGB_LED_R_PIN EXP1_05_PIN #endif #ifndef RGB_LED_G_PIN #define RGB_LED_G_PIN EXP1_04_PIN #endif #ifndef RGB_LED_B_PIN #define RGB_LED_B_PIN EXP1_03_PIN #endif #elif ENABLED(FYSETC_MINI_12864_2_1) #define NEOPIXEL_PIN EXP1_05_PIN #endif #endif // !FYSETC_MINI_12864 #if IS_ULTIPANEL #define LCD_PINS_D5 EXP1_05_PIN #define LCD_PINS_D6 EXP1_04_PIN #define LCD_PINS_D7 EXP1_03_PIN #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder #endif #endif #endif #endif // HAS_WIRED_LCD // Alter timing for graphical display #if IS_U8GLIB_ST7920 #define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_3 600 #endif #if ENABLED(TOUCH_UI_FTDI_EVE) #define BEEPER_PIN EXP1_10_PIN #define CLCD_MOD_RESET EXP2_08_PIN #define CLCD_SPI_CS EXP2_06_PIN #endif