/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once #define ALLOW_STM32DUINO #include "env_validate.h" #if HOTENDS > 6 || E_STEPPERS > 6 #error "FLYF407ZG supports up to 6 hotends / E-steppers." #endif #define BOARD_INFO_NAME "FLYF407ZG" #define BOARD_WEBSITE_URL "github.com/FLYmaker/FLYF407ZG" #define DEFAULT_MACHINE_NAME BOARD_INFO_NAME // Avoid conflict with fans and TIMER_TONE #define TEMP_TIMER 3 #define STEP_TIMER 5 // // EEPROM Emulation // #if NO_EEPROM_SELECTED #define FLASH_EEPROM_EMULATION //#define SRAM_EEPROM_EMULATION //#define I2C_EEPROM #endif #if ENABLED(FLASH_EEPROM_EMULATION) // Decrease delays and flash wear by spreading writes across // the 128kB sector allocated for EEPROM emulation. #define FLASH_EEPROM_LEVELING #elif ENABLED(I2C_EEPROM) #define MARLIN_EEPROM_SIZE 0x2000 // 8K #endif #ifndef MARLIN_EEPROM_SIZE #define MARLIN_EEPROM_SIZE 0x1000 // 4K #endif // // Servos // #define SERVO0_PIN PE11 // // Limit Switches // #define X_MIN_PIN PC3 #define X_MAX_PIN PC2 #define Y_MIN_PIN PF2 #define Y_MAX_PIN PF1 #define Z_MIN_PIN PF0 #define Z_MAX_PIN PC15 // // Z Probe (when not Z_MIN_PIN) // #define Z_MIN_PROBE_PIN PC14 // Z3_PIN // // Steppers // #define X_STEP_PIN PB9 #define X_DIR_PIN PE0 #define X_ENABLE_PIN PE1 #ifndef X_CS_PIN #define X_CS_PIN PG13 #endif #define Y_STEP_PIN PB8 #define Y_DIR_PIN PG11 #define Y_ENABLE_PIN PG12 #ifndef Y_CS_PIN #define Y_CS_PIN PG10 #endif #define Z_STEP_PIN PA8 #define Z_DIR_PIN PD6 #define Z_ENABLE_PIN PD7 #ifndef Z_CS_PIN #define Z_CS_PIN PD5 #endif #define E0_STEP_PIN PC7 #define E0_DIR_PIN PD3 #define E0_ENABLE_PIN PD4 #ifndef E0_CS_PIN #define E0_CS_PIN PD1 #endif #define E1_STEP_PIN PC6 #define E1_DIR_PIN PA15 #define E1_ENABLE_PIN PD0 #ifndef E1_CS_PIN #define E1_CS_PIN PA14 #endif #define E2_STEP_PIN PD15 #define E2_DIR_PIN PG7 #define E2_ENABLE_PIN PG8 #ifndef E2_CS_PIN #define E2_CS_PIN PG6 #endif #define E3_STEP_PIN PD14 #define E3_DIR_PIN PG4 #define E3_ENABLE_PIN PG5 #ifndef E3_CS_PIN #define E3_CS_PIN PG3 #endif #define E4_STEP_PIN PD13 #define E4_DIR_PIN PD11 #define E4_ENABLE_PIN PG2 #ifndef E4_CS_PIN #define E4_CS_PIN PD10 #endif #define E5_STEP_PIN PD12 #define E5_DIR_PIN PD8 #define E5_ENABLE_PIN PD9 #ifndef E5_CS_PIN #define E5_CS_PIN PB12 #endif // // Temperature Sensors // #define TEMP_0_PIN PA0 // Analog Input #define TEMP_1_PIN PC1 // Analog Input #define TEMP_2_PIN PC0 // Analog Input #define TEMP_3_PIN PF10 // Analog Input #define TEMP_4_PIN PF5 // Analog Input #define TEMP_5_PIN PF4 // Analog Input #define TEMP_BED_PIN PF3 // Analog Input // // Heaters / Fans // #define HEATER_0_PIN PF7 #define HEATER_1_PIN PF6 #define HEATER_2_PIN PE6 #define HEATER_3_PIN PE5 #define HEATER_4_PIN PE4 #define HEATER_5_PIN PE3 #define HEATER_BED_PIN PE2 #ifndef FAN_PIN #define FAN_PIN PF8 #endif #define FAN1_PIN PF9 #define FAN2_PIN PA2 #define FAN3_PIN PA1 #define FAN4_PIN PE13 #define FAN5_PIN PB11 /** * ------ ------ * PB10 |10 9 | PE15 PB14 |10 9 | PB13 * PE14 | 8 7 | PE12 PC5 | 8 7 | PF11 * PE10 6 5 | PE9 PC4 6 5 | PB15 * PE8 | 4 3 | PE7 PB2 | 4 3 | RESET * GND | 2 1 | 5V GND | 2 1 | -- * ------ ------ * EXP1 EXP2 */ #define EXP1_03_PIN PE7 #define EXP1_04_PIN PE8 #define EXP1_05_PIN PE9 #define EXP1_06_PIN PE10 #define EXP1_07_PIN PE12 #define EXP1_08_PIN PE14 #define EXP1_09_PIN PE15 #define EXP1_10_PIN PB10 #define EXP2_03_PIN -1 // RESET #define EXP2_04_PIN PB2 #define EXP2_05_PIN PB15 #define EXP2_06_PIN PC4 #define EXP2_07_PIN PF11 #define EXP2_08_PIN PC5 #define EXP2_09_PIN PB13 #define EXP2_10_PIN PB14 // // Onboard SD support // //#define SD_CARD_DETECT_PIN PC13 #ifndef SDCARD_CONNECTION #define SDCARD_CONNECTION ONBOARD #endif #if SD_CONNECTION_IS(ONBOARD) #define SDIO_SUPPORT // Use SDIO for onboard SD #if DISABLED(SDIO_SUPPORT) #define SOFTWARE_SPI // Use soft SPI for onboard SD #define SDSS PC11 #define SD_SCK_PIN PC12 #define SD_MISO_PIN PC8 #define SD_MOSI_PIN PD2 #endif #elif SD_CONNECTION_IS(LCD) #define SD_SCK_PIN EXP2_09_PIN #define SD_MISO_PIN EXP2_10_PIN #define SD_MOSI_PIN EXP2_05_PIN #define SDSS EXP2_07_PIN #define SD_DETECT_PIN EXP2_04_PIN #endif // // Trinamic Software SPI // #if ENABLED(TMC_USE_SW_SPI) #ifndef TMC_SW_SCK #define TMC_SW_SCK EXP2_09_PIN #endif #ifndef TMC_SW_MISO #define TMC_SW_MISO EXP2_10_PIN #endif #ifndef TMC_SW_MOSI #define TMC_SW_MOSI EXP2_05_PIN #endif #endif // // Trinamic Software Serial // #if HAS_TMC_UART #define X_SERIAL_TX_PIN PG13 #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN #define Y_SERIAL_TX_PIN PG10 #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN #define Z_SERIAL_TX_PIN PD5 #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN #define E0_SERIAL_TX_PIN PD1 #define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN #define E1_SERIAL_TX_PIN PA14 #define E1_SERIAL_RX_PIN E1_SERIAL_TX_PIN #define E2_SERIAL_TX_PIN PG6 #define E2_SERIAL_RX_PIN E2_SERIAL_TX_PIN #define E3_SERIAL_TX_PIN PG3 #define E3_SERIAL_RX_PIN E3_SERIAL_TX_PIN #define E4_SERIAL_TX_PIN PD10 #define E4_SERIAL_RX_PIN E4_SERIAL_TX_PIN #define E5_SERIAL_TX_PIN PB12 #define E5_SERIAL_RX_PIN E5_SERIAL_TX_PIN #endif // // LCD / Controller // #if IS_RRD_SC #define BEEPER_PIN EXP1_10_PIN #define LCD_PINS_RS EXP1_07_PIN #define LCD_PINS_ENABLE EXP1_08_PIN #define LCD_PINS_D4 EXP1_06_PIN #define LCD_PINS_D5 EXP1_05_PIN #define LCD_PINS_D6 EXP1_04_PIN #define LCD_PINS_D7 EXP1_03_PIN #define BTN_EN1 EXP2_06_PIN #define BTN_EN2 EXP2_08_PIN #define BTN_ENC EXP1_09_PIN #endif // // Filament runout // #define FIL_RUNOUT_PIN PA3 // Alter timing for graphical display #if IS_U8GLIB_ST7920 #define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_3 715 #endif