/** * Marlin 3D Printer Firmware * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once #include "env_validate.h" #define BOARD_INFO_NAME "ZONESTAR ZM3E2 V1.0" #define DISABLE_DEBUG //#define DISABLE_JTAG #if NO_EEPROM_SELECTED #define FLASH_EEPROM_EMULATION #define EEPROM_PAGE_SIZE (0x800) // 2K #define EEPROM_START_ADDRESS (0x08000000 + (STM32_FLASH_SIZE) * 1024 - 2 * EEPROM_PAGE_SIZE) #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE // 2K #endif //============================================================================= // Zonestar ZM3E2 V1.0 (STM32F103RCT6) board pin assignments //============================================================================= // PA0 PWR_HOLD | PB0 BEEP | PC0 HEATER_0 // PA1 FAN_PIN | PB1 KILL | PC1 HEATER_BED // PA2 TX2 | PB2 LCD_SDA | PC2 TEMP_BED // PA3 RX2 | PB3 E1_EN | PC3 TEMP_E0 // PA4 SD_CS | PB4 Z_STOP | PC4 SD_DETECT // PA5 SD_SCK | PB5 Z_DIR | PC5 BTN_EN2 // PA6 SD_MISO | PB6 Z_STEP | PC6 FAN1 // PA7 SD_MOSI | PB7 Z_EN | PC7 FIL_RUNOUT // PA8 X_DIR | PB8 Y_STEP | PC8 X_EN // PA9 LCD_RS | PB9 Y_DIR | PC9 X_STEP // PA10 LCD_SCK | PB10 BTN_ENC | PC10 Z_MIN_PROBE_PIN // PA11 USB_D- | PB11 BTN_EN1 | PC11 FIL_RUNOUT2 // PA12 USB_D+ | PB12 LED | PC12 E1_DIR // PA13 MS1 | PB13 E0_EN | PC13 Y_STOP // PA14 MS2 | PB14 E0_STEP | PC14 Y_EN // PA15 PWM | PB15 E0_DIR | PC15 X_STOP // PD0 NC // PD1 NC // PD2 E1_STEP //============================================================================= // EXP1 connector // MARK I/O ZONESTAR_12864LCD ZONESTAR_12864OLED // 10 MOSI PB1 KILL SDA // 9 SCK PB0 BEEP SCK // 8 TX1 PA9 DOGLCD_CS CS // 7 RX1 PA10 DOGLCD_SCK DC // 6 ENA PC5 BTN_EN2 KNOB_ENB // 5 DAT PB2 DOGLCD_MOSI RESET // 4 TX3 PB10 BTN_ENC KNOB_ENC // 3 RX3 PB11 BTN_EN1 KNOB_ENA // 2 +5V // 1 GND #define EXP1_03_PIN PB11 #define EXP1_04_PIN PB10 #define EXP1_05_PIN PB2 #define EXP1_06_PIN PC5 #define EXP1_07_PIN PA10 #define EXP1_08_PIN PA9 #define EXP1_09_PIN PB0 #define EXP1_10_PIN PB1 // AUX1 connector // 1 +5V // 2 TX2 PA2 UART2_TX // 3 RX2 PA3 UART2_RX // 4 GND // AUX2 connector to BLTouch // 1 +5V // 2 SEN PC10 // 3 PWM PA15 // 4 GND //============================================================================= // // Servos // #define SERVO0_PIN PA15 // // Limit Switches // #define X_STOP_PIN PC15 #define Y_STOP_PIN PC13 #define Z_STOP_PIN PB4 #ifndef Z_MIN_PROBE_PIN #define Z_MIN_PROBE_PIN PC10 // BLTouch (3DTouch) #endif // // Filament Runout Sensor // #define FIL_RUNOUT_PIN PC7 // E0_SW //#define FIL_RUNOUT2_PIN PC11 // E1_SW // // Steppers // #define MS1_PIN PA13 #define MS2_PIN PA14 #define X_STEP_PIN PC9 #define X_DIR_PIN PA8 #define X_ENABLE_PIN PC8 #define Y_STEP_PIN PB8 #define Y_DIR_PIN PB9 #define Y_ENABLE_PIN PC14 #define Z_STEP_PIN PB6 #define Z_DIR_PIN PB5 #define Z_ENABLE_PIN PB7 #define E0_STEP_PIN PB14 #define E0_DIR_PIN PB15 #define E0_ENABLE_PIN PB13 #define E1_STEP_PIN PD2 #define E1_DIR_PIN PC12 #define E1_ENABLE_PIN PB3 // // Heaters / Fans // #define HEATER_0_PIN PC0 // EXTRUDER 1 #define HEATER_BED_PIN PC1 // BED #define FAN1_PIN PC6 #define FAN_PIN PA1 // // Temperature Sensors // #define TEMP_BED_PIN PC2 // Analog Input #define TEMP_0_PIN PC3 // Analog Input #define LED_PIN PB12 //#define KILL_PIN PB1 // @EXP1 #define SUICIDE_PIN PA0 // // SD card // #define ENABLE_SPI1 #define SD_DETECT_PIN PC4 #define SD_SCK_PIN PA5 #define SD_MISO_PIN PA6 #define SD_MOSI_PIN PA7 #define SD_SS_PIN PA4 // // LCD Pins // #if ENABLED(ZONESTAR_12864LCD) //================================================================================ // LCD 128x64 //================================================================================ // EXP1 connector // MARK I/O ZONESTAR_12864LCD // 10 MOSI PB1 KILL // 9 SCK PB0 BEEP // 8 TX1 PA9 LCD_PINS_RS // 7 RX1 PA10 LCD_PINS_D4 // 6 ENA PC5 BTN_EN2 // 5 DAT PB2 LCD_PINS_ENABLE // 4 TX3 PB10 BTN_ENC // 3 RX3 PB11 BTN_EN1 // 2 +5V // 1 GND #define LCDSCREEN_NAME "ZONESTAR LCD12864" #define LCD_PINS_RS EXP1_08_PIN #define LCD_PINS_ENABLE EXP1_05_PIN #define LCD_PINS_D4 EXP1_07_PIN //#define KILL_PIN EXP1_10_PIN #define BEEPER_PIN EXP1_09_PIN #define BTN_EN1 EXP1_03_PIN #define BTN_EN2 EXP1_06_PIN #define BTN_ENC EXP1_04_PIN #define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_2 200 #define BOARD_ST7920_DELAY_3 125 #elif EITHER(ZONESTAR_12864OLED, ZONESTAR_12864OLED_SSD1306) //================================================================================ // OLED 128x64 //================================================================================ // 10 MOSI PB1 OLED_SDA // 9 SCK PB0 OLED_SCK // 8 TX1 PA9 OLED_CS // 7 RX1 PA10 OLED_DC // 6 ENA PC5 KNOB_ENA // 5 DAT PB2 OLED_RESET // 4 TX3 PB10 KNOB_ENC // 3 RX3 PB11 KNOB_ENB #define FORCE_SOFT_SPI #define LCDSCREEN_NAME "ZONESTAR 12864OLED" #define LCD_PINS_RS EXP1_05_PIN // = LCD_RESET_PIN #define LCD_PINS_DC EXP1_07_PIN // DC #define DOGLCD_CS EXP1_08_PIN // CS #define DOGLCD_A0 LCD_PINS_DC #define DOGLCD_MOSI EXP1_10_PIN // SDA #define DOGLCD_SCK EXP1_09_PIN // SCK // Encoder #define BTN_EN1 EXP1_03_PIN #define BTN_EN2 EXP1_06_PIN #define BTN_ENC EXP1_04_PIN #endif