/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once /** * ANYCUBIC Trigorilla Pro (STM32F103ZET6) board pin assignments. * It is the same used by the Tronxy X5SA thanks to ftoz1 for sharing it * https://github.com/MarlinFirmware/Marlin/issues/14655 * https://github.com/MarlinFirmware/Marlin/files/3401484/x5sa-main_board-2.pdf */ #include "env_validate.h" #if HOTENDS > 2 || E_STEPPERS > 2 #error "Trigorilla Pro supports up to 2 hotends / E-steppers. Comment out this line to continue." #endif #define BOARD_INFO_NAME "Trigorilla Pro" #define BOARD_NO_NATIVE_USB #define DISABLE_JTAG //#define SWAPPED_Z_PLUGS // // EEPROM // #if NO_EEPROM_SELECTED #define FLASH_EEPROM_EMULATION #endif #if ENABLED(FLASH_EEPROM_EMULATION) // SoC Flash (framework-arduinoststm32-maple/STM32F1/libraries/EEPROM/EEPROM.h) #define EEPROM_START_ADDRESS (0x8000000UL + (512 * 1024) - 2 * EEPROM_PAGE_SIZE) #define EEPROM_PAGE_SIZE (0x800U) // 2K, but will use 2x more (4K) #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE #else #define MARLIN_EEPROM_SIZE (0x800U) // On SD, Limit to 2K, require this amount of RAM #endif // // Limit Switches // #define X_STOP_PIN PG10 #define Y_STOP_PIN PA12 #ifndef Z_MIN_PIN #ifdef SWAPPED_Z_PLUGS #define Z_MIN_PIN PA14 #else #define Z_MIN_PIN PA13 #endif #endif #ifndef Z_MAX_PIN #ifdef SWAPPED_Z_PLUGS #define Z_MAX_PIN PA13 #else #define Z_MAX_PIN PA14 #endif #endif // // Steppers // #define X_ENABLE_PIN PC13 #define X_STEP_PIN PE5 #define X_DIR_PIN PE6 #define Y_ENABLE_PIN PE4 #define Y_STEP_PIN PE2 #define Y_DIR_PIN PE3 #define Z_ENABLE_PIN PE1 #define Z_STEP_PIN PB9 #define Z_DIR_PIN PE0 #define E0_ENABLE_PIN PB8 #define E0_STEP_PIN PB4 #define E0_DIR_PIN PB5 #define E1_ENABLE_PIN PG8 #define E1_STEP_PIN PC7 #define E1_DIR_PIN PC6 // // Temperature Sensors // #define TEMP_0_PIN PA1 // TH1 #define TEMP_BED_PIN PA0 // TB1 // // Heaters // #define HEATER_0_PIN PG12 // HEATER1 #define HEATER_BED_PIN PG11 // HOT BED #define HEATER_BED_INVERTING true // // Fans // #define CONTROLLER_FAN_PIN PD6 // FAN #define FAN_PIN PG13 // FAN #define FAN1_PIN PG14 // FAN // // Misc // #define BEEPER_PIN PB0 #define LED_PIN PD3 //#define POWER_LOSS_PIN PG2 // PG4 PW_DET #define FIL_RUNOUT_PIN PA15 // MT_DET // // TFT with FSMC interface // #if HAS_FSMC_TFT /** * Note: MKS Robin TFT screens use various TFT controllers * Supported screens are based on the ILI9341, ST7789V and ILI9328 (320x240) * ILI9488 is not supported. * Define init sequences for other screens in u8g_dev_tft_320x240_upscale_from_128x64.cpp * * If the screen stays white, disable 'LCD_RESET_PIN' to let the bootloader init the screen. * * Setting an 'LCD_RESET_PIN' may cause a flicker when entering the LCD menu * because Marlin uses the reset as a failsafe to revive a glitchy LCD. */ #define TFT_RESET_PIN PF11 #define TFT_BACKLIGHT_PIN PD13 #define FSMC_CS_PIN PD7 // NE4 #define FSMC_RS_PIN PD11 // A0 #define TFT_CS_PIN FSMC_CS_PIN #define TFT_RS_PIN FSMC_RS_PIN #define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT #define FSMC_DMA_DEV DMA2 #define FSMC_DMA_CHANNEL DMA_CH5 #define ANYCUBIC_TFT35 #else #define LCD_RESET_PIN PF11 #define LCD_BACKLIGHT_PIN PD13 #endif // XPT2046 Touch Screen calibration #if ANY(TFT_COLOR_UI, TFT_LVGL_UI, TFT_CLASSIC_UI) #ifndef TOUCH_CALIBRATION_X #define TOUCH_CALIBRATION_X -17181 #endif #ifndef TOUCH_CALIBRATION_Y #define TOUCH_CALIBRATION_Y 11434 #endif #ifndef TOUCH_OFFSET_X #define TOUCH_OFFSET_X 501 #endif #ifndef TOUCH_OFFSET_Y #define TOUCH_OFFSET_Y -9 #endif #endif #if NEED_TOUCH_PINS #define TOUCH_CS_PIN PB7 // SPI2_NSS #define TOUCH_SCK_PIN PA5 // SPI2_SCK #define TOUCH_MISO_PIN PA6 // SPI2_MISO #define TOUCH_MOSI_PIN PA7 // SPI2_MOSI #endif // SPI1(PA7) & SPI3(PB5) not available #define SPI_DEVICE 2 #if ENABLED(SDIO_SUPPORT) #define SD_SCK_PIN PB13 // SPI2 ok #define SD_MISO_PIN PB14 // SPI2 ok #define SD_MOSI_PIN PB15 // SPI2 ok #define SD_SS_PIN PC11 // PB12 is X- ok #define SD_DETECT_PIN -1 // SD_CD ok #else // SD as custom software SPI (SDIO pins) #define SD_SCK_PIN PC12 #define SD_MISO_PIN PC8 #define SD_MOSI_PIN PD2 #define SD_SS_PIN -1 #define ONBOARD_SD_CS_PIN PC11 #define SDSS PD2 #define SD_DETECT_PIN -1 #endif #undef SWAPPED_Z_PLUGS