/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once #include "env_validate.h" #define BOARD_INFO_NAME "FLY_MINI" #define BOARD_WEBSITE_URL "github.com/FLYmaker/FLY-MINI" #define DISABLE_JTAG // // Flash EEPROM Emulation // #if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION) #define FLASH_EEPROM_EMULATION #define EEPROM_PAGE_SIZE 0x800 // 2K #define EEPROM_START_ADDRESS (0x8000000 + 256 * 1024 - 2 * EEPROM_PAGE_SIZE) // 256K firmware space #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE #endif // // Servos // #define SERVO0_PIN PA8 // // Limit Switches // #define X_MIN_PIN PC12 #define X_MAX_PIN PC11 #define Y_MIN_PIN PC10 #define Y_MAX_PIN PA15 #define Z_MIN_PIN PA14 #define Z_MAX_PIN PA13 // // Steppers // #define X_STEP_PIN PB1 #define X_DIR_PIN PB2 #define X_ENABLE_PIN PB10 #ifndef X_CS_PIN #define X_CS_PIN PB0 #endif #define Y_STEP_PIN PA2 #define Y_DIR_PIN PC4 #define Y_ENABLE_PIN PC5 #ifndef Y_CS_PIN #define Y_CS_PIN PA7 #endif #define Z_STEP_PIN PA3 #define Z_DIR_PIN PA5 #define Z_ENABLE_PIN PA6 #ifndef Z_CS_PIN #define Z_CS_PIN PA4 #endif #define E0_STEP_PIN PA1 #define E0_DIR_PIN PC3 #define E0_ENABLE_PIN PA0 #ifndef E0_CS_PIN #define E0_CS_PIN PC2 #endif #if ENABLED(TMC_USE_SW_SPI) #ifndef TMC_SW_MOSI #define TMC_SW_MOSI EXP2_05_PIN #endif #ifndef TMC_SW_MISO #define TMC_SW_MISO EXP2_10_PIN #endif #ifndef TMC_SW_SCK #define TMC_SW_SCK EXP2_09_PIN #endif #endif #if HAS_TMC_UART #define X_SERIAL_TX_PIN PB0 #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN #define Y_SERIAL_TX_PIN PA7 #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN #define Z_SERIAL_TX_PIN PA4 #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN #define E0_SERIAL_TX_PIN PC2 #define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN #endif // // Heaters / Fans // #define HEATER_0_PIN PC6 #define HEATER_BED_PIN PC7 #ifndef FAN_PIN #define FAN_PIN PC8 #endif #define FAN1_PIN PC9 // // Temperature Sensors // #define TEMP_BED_PIN PC0 // Analog Input #define TEMP_0_PIN PC1 // Analog Input /** ------ ------ * (BEEPER) PC14 |10 9 | PC13 (BTN_ENC) (MISO) PB14 |10 9 | PB13 (SD_SCK) * (LCD_EN) PB9 | 8 7 | PB8 (LCD_RS) (BTN_EN1) PB3 | 8 7 | PB12 (SD_CS2) * (LCD_D4) PB7 6 5 | PB6 (LCD_D5) (BTN_EN2) PD2 6 5 | PB15 (SD_MOSI) * (LCD_D6) PB5 | 4 3 | PB4 (LCD_D7) (SD_DETECT) PB11 | 4 3 | RESET * GND | 2 1 | 5V GND | 2 1 | -- * ------ ------ * EXP1 EXP2 */ #define EXP1_03_PIN PB4 #define EXP1_04_PIN PB5 #define EXP1_05_PIN PB6 #define EXP1_06_PIN PB7 #define EXP1_07_PIN PB8 #define EXP1_08_PIN PB9 #define EXP1_09_PIN PC13 #define EXP1_10_PIN PC14 #define EXP2_03_PIN -1 // RESET #define EXP2_04_PIN PB11 #define EXP2_05_PIN PB15 #define EXP2_06_PIN PD2 #define EXP2_07_PIN PB12 #define EXP2_08_PIN PB3 #define EXP2_09_PIN PB13 #define EXP2_10_PIN PB14 // // LCD / Controller // #if HAS_WIRED_LCD #define SPI_DEVICE 2 #define SD_SS_PIN EXP2_07_PIN #define SD_SCK_PIN EXP2_09_PIN #define SD_MISO_PIN EXP2_10_PIN #define SD_MOSI_PIN EXP2_05_PIN #define SDSS SD_SS_PIN #define SD_DETECT_PIN EXP2_04_PIN #define BEEPER_PIN EXP1_10_PIN #define LCD_PINS_RS EXP1_07_PIN #define LCD_PINS_ENABLE EXP1_08_PIN #define LCD_PINS_D4 EXP1_06_PIN #define LCD_PINS_D5 EXP1_05_PIN #define LCD_PINS_D6 EXP1_04_PIN #define LCD_PINS_D7 EXP1_03_PIN #define BTN_EN1 EXP2_06_PIN #define BTN_EN2 EXP2_08_PIN #define BTN_ENC EXP1_09_PIN #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder #endif // Alter timing for graphical display #if IS_U8GLIB_ST7920 #define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_3 715 #endif #endif // HAS_WIRED_LCD