/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once #define ALLOW_MEGA644P #include "env_validate.h" #define BOARD_INFO_NAME "Zonestar ZMIB_V2" #define BOARD_WEBSITE_URL "www.aliexpress.com/item/32957490744.html" #define IS_ZMIB_V2 /** * ZMIB pin assignments * * The ZMIB board needs a bootloader installed before Marlin can be uploaded. * If you don't have a chip programmer you can use a spare Arduino plus a few * electronic components to write the bootloader. * * See http://www.instructables.com/id/Burn-Arduino-Bootloader-with-Arduino-MEGA/ */ /** * PIN: 0 Port: B0 HEATER_0_PIN * PIN: 1 Port: B1 HEATER_BED_PIN * PIN: 2 Port: B2 EXP1_4(BTN_EN2) * PIN: 3 Port: B3 V1: SD_DETECT_PIN * PIN: 3 Port: B3 V2: EXP1_6 * PIN: 4 Port: B4 SDSS * PIN: 4 Port: B4 V1: EXP1_6 * PIN: 5 Port: B5 AVR_MOSI_PIN * . SD_MOSI_PIN * PIN: 6 Port: B6 AVR_MISO_PIN * . EXP1_9(SD_MISO_PIN) * PIN: 7 Port: B7 AVR_SCK_PIN * . EXP1_10(SD_SCK_PIN) * PIN: 8 Port: D0 RXD * PIN: 9 Port: D1 TXD * PIN: 10 Port: D2 EXP1_8 * PIN: 11 Port: D3 EXP1_7 * PIN: 12 Port: D4 EXP1_5(BTN_EN1) * PIN: 13 Port: D5 Z_MIN_PIN * PIN: 14 Port: D6 E1_DIR_PIN * PIN: 15 Port: D7 E1_STEP_PIN * PIN: 16 Port: C0 Z_DIR_PIN * PIN: 17 Port: C1 Z_STEP_PIN * PIN: 18 Port: C2 Y_MIN_PIN * PIN: 19 Port: C3 Y_DIR_PIN * PIN: 20 Port: C4 Y_STEP_PIN * PIN: 21 Port: C5 X_MIN_PIN * PIN: 22 Port: C6 X_DIR_PIN * PIN: 23 Port: C7 X_STEP_PIN * PIN: 24 Port: A7 X_ENABLE_PIN * Y_ENABLE_PIN * Z_ENABLE_PIN * E0_ENABLE_PIN * E1_ENABLE_PIN * PIN: 25 Port: A6 FIL_RUNOUT_PIN * PIN: 26 Port: A5 E0_DIR_PIN * PIN: 27 Port: A4 E0_STEP_PIN * PIN: 28 Port: A3 FAN_PIN * PIN: 29 Port: A2 EXP1_3(BTN_ENC) * ADC_KEY_PIN * PIN: 30 Port: A1 TEMP_0_PIN * PIN: 31 Port: A0 TEMP_BED_PIN */ // // Limit Switches // #define X_MIN_PIN 21 #define Y_MIN_PIN 18 #if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT) #define Z_MIN_PIN 25 #else #define Z_MIN_PIN 13 #endif // // Steppers // #define X_STEP_PIN 23 #define X_DIR_PIN 22 #define X_ENABLE_PIN 24 #define Y_STEP_PIN 20 #define Y_DIR_PIN 19 #define Y_ENABLE_PIN 24 #if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT) #define Z_STEP_PIN 27 #define Z_DIR_PIN 26 #else #define Z_STEP_PIN 17 #define Z_DIR_PIN 16 #endif #define Z_ENABLE_PIN 24 #if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT) #define E0_STEP_PIN 15 #define E0_DIR_PIN 14 #else #define E0_STEP_PIN 27 #define E0_DIR_PIN 26 #endif #define E0_ENABLE_PIN 24 #define E1_STEP_PIN 15 #define E1_DIR_PIN 14 #define E1_ENABLE_PIN 24 // // Temperature Sensors // #define TEMP_0_PIN 1 // Analog Input #define TEMP_BED_PIN 0 // Analog Input // // Heaters / Fans // #define HEATER_0_PIN 0 #define HEATER_BED_PIN 1 #define FAN_PIN 28 #define FAN1_PIN -1 // // Filament Runout Sensor // #if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT) #define FIL_RUNOUT_PIN 13 #else #define FIL_RUNOUT_PIN 25 // Z-MIN #endif // // SD card // #if ENABLED(SDSUPPORT) #define SDSS 4 #endif #define SD_DETECT_PIN -1 /** EXP1 * ------ * (MOSI) D5 |10 9 | D7 (SCK) * (CS) D11 | 8 7 | D10 (DC/D4) * (EN2) D12 6 5 | D4 or D3 (EN/RS) * (ENC) D29 | 4 3 | D2 (EN1) * (GND) | 2 1 | (5V) * ------ */ #define EXP1_03_PIN 2 #define EXP1_04_PIN 29 #ifndef IS_ZMIB_V2 #define EXP1_05_PIN 4 // ZMIB V1 #else #define EXP1_05_PIN 3 // ZMIB V2 #endif #define EXP1_06_PIN 12 #define EXP1_07_PIN 10 #define EXP1_08_PIN 11 #define EXP1_09_PIN 7 #define EXP1_10_PIN 5 #if ENABLED(ZONESTAR_12864LCD) // // LCD 128x64 // #define LCDSCREEN_NAME "ZONESTAR_12864LCD" #define FORCE_SOFT_SPI //#define LCD_SDSS EXP1_08_PIN #define LCD_PINS_RS EXP1_08_PIN // ST7920_CS_PIN (LCD module pin 4) #define LCD_PINS_ENABLE EXP1_05_PIN // ST7920_DAT_PIN (LCD module pin 5) #define LCD_PINS_D4 EXP1_07_PIN // ST7920_CLK_PIN (LCD module pin 6) #define BOARD_ST7920_DELAY_1 DELAY_2_NOP #define BOARD_ST7920_DELAY_2 DELAY_2_NOP #define BOARD_ST7920_DELAY_3 DELAY_2_NOP #elif EITHER(ZONESTAR_12864OLED, ZONESTAR_12864OLED_SSD1306) // // OLED 128x64 // #define LCDSCREEN_NAME "ZONESTAR 12864OLED" #define FORCE_SOFT_SPI #define LCD_PINS_RS EXP1_05_PIN #define LCD_PINS_DC EXP1_07_PIN #define DOGLCD_CS EXP1_08_PIN #if ENABLED(OLED_HW_IIC) #error "Oops! can't choose HW IIC for ZMIB board!!" #else #define DOGLCD_A0 LCD_PINS_DC #if DISABLED(OLED_HW_SPI) #define DOGLCD_MOSI AVR_MOSI_PIN // Software SPI #define DOGLCD_SCK AVR_SCK_PIN #endif #endif #endif // // All the above are also RRDSC with rotary encoder // #if IS_RRD_SC #define BTN_EN1 EXP1_03_PIN #define BTN_EN2 EXP1_06_PIN #define BTN_ENC EXP1_04_PIN #define BEEPER_PIN -1 #define KILL_PIN -1 #endif