/** * Marlin 3D Printer Firmware * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once /** * BRICOLEMON LITE Board. Based on atsamd51 (AGCM4), bootloader and credits by ADAFRUIT. * This board its a 3.3V LOGIC Board, following the ADAFRUIT example, all of the board is open source. * Schematic: Refer to the Bricolemon * 3DSTEP: https://github.com/bricogeek/bricolemon/blob/master/Documentacion/Bricolemon%20Lite/LC_BG_002_PCB_V1I4.step * PinDemux: https://github.com/bricogeek/bricolemon/blob/master/Documentacion/Bricolemon/PinDEMUX.xlsx * * NOTE: We need the Serial port on the -1 to make it work!!. Remember to change it on configuration.h #define SERIAL_PORT -1 */ #if NOT_TARGET(ARDUINO_GRAND_CENTRAL_M4) #error "Oops! Select 'Adafruit Grand Central M4' in 'Tools > Board.'" #endif #ifndef BOARD_INFO_NAME #define BOARD_INFO_NAME "BRICOLEMON LITE V1.0" // , Lemoncrest & BricoGeek collaboration. #endif /** * EEPROM EMULATION: Works with some bugs already, but the board needs an I2C EEPROM memory soldered on. */ //#define FLASH_EEPROM_EMULATION #define I2C_EEPROM // EEPROM on I2C-0 #define MARLIN_EEPROM_SIZE 0x10000 // 64K (CAT24C512) // This is another option to emulate an EEPROM, but it's more efficient to not lose the data in the first place. //#define SDCARD_EEPROM_EMULATION // // BLTOUCH PIN: This pin is the signal pin for the BLTOUCH sensor. // #define SERVO0_PIN 33 // BLTouch PWM // // Limit Switches // #define X_STOP_PIN 10 #define Y_STOP_PIN 11 #define Z_STOP_PIN 12 // // Z Probe (when not Z_MIN_PIN) // #ifndef Z_MIN_PROBE_PIN #define Z_MIN_PROBE_PIN 12 #endif // // Steppers // #define X_STEP_PIN 3 #define X_DIR_PIN 22 #define X_ENABLE_PIN 26 #define Y_STEP_PIN 4 #define Y_DIR_PIN 23 #define Y_ENABLE_PIN 27 #define Z_STEP_PIN 5 #define Z_DIR_PIN 24 #define Z_ENABLE_PIN 28 #define E0_STEP_PIN 2 #define E0_DIR_PIN 25 #define E0_ENABLE_PIN 29 // Filament runout. You may choose to use this pin for some other purpose. It's a normal GPIO that can be configured as I/O. // For example, a switch to detect any kind of behavior, Power supply pin .... etc. #define FIL_RUNOUT_PIN 32 // // Temperature Sensors // #define TEMP_0_PIN 1 #define TEMP_BED_PIN 3 // // Heaters / Fans // #define HEATER_0_PIN 6 #define HEATER_BED_PIN 7 #define FAN_PIN 8 #define FAN1_PIN 9 // // LCD / Controller // /** * Bricolemon Expansion connectors * * ------ ------ * VCC | 1 2 | GND KILL | 1 2 | GND * LCD7 | 3 4 | LCDD6 RESET | 3 4 | SD_DETECT * LCD5 | 5 6 LCDD4 MOSI | 5 6 BTN_EN1 * LCDRS | 7 8 | LCDDE SS | 7 8 | BTN_EN2 * BTN_ENCODER | 9 10 | BEEPER SCLK | 9 10 | MISO * ------ ------ * EXP1 EXP2 * *- This extra connector is for a serial display like the MKS TFT. * MKS TFT * ------ * RX0 | . . | NC * TX0 | . . NC * GND | . . GND * 5B | . . | 5V * ------ * *- Special mapping of EXP1 to EXP3 to work with Ender displays. * * Enable CR10_STOCKDISPLAY in Configuration.h and connect EXP1 to the display EXP3 with this mapping. * ------ * VCC | 1 2 | GND * LCDDE | 3 4 | LCDRS * LCDD4 | 5 6 BTN_EN2 * RESET | 7 8 | BTN_EN1 * BTN_ENCODER | 9 10 | BEEPER * ------ * *- Digital pinout reference of the Bricolemon for advanced users/configurations. * * ------ ------ * VCC | 1 2 | GND D49 | 1 2 | GND * D39 | 3 4 | D38 RST | 3 4 | D44 * D37 | 5 6 D36 D51 | 5 6 D42 * D34 | 7 8 | D35 D53 | 7 8 | D43 * D40 | 9 10 | D41 D52 | 9 10 | D50 * ------ ------ * EXP1 EXP2 * *- Pin table overview * LCD--- SPI--- * LCD4 36 MISO 50 * LCD5 37 SS 53 * LCD6 38 SCKL 52 * LCD7 39 MOSI 51 * LCDRS 34 BEEPER * LCDDE 35 BEEP 41 * ENCODER--- SD-CARD--- * BTN_EN1 42 * BTN_EN2 43 SD_DETECT 44 * BTN_ENCODER 40 KILL_PIN 49 */ #define EXP1_03_PIN 39 #define EXP1_04_PIN 38 #define EXP1_05_PIN 37 #define EXP1_06_PIN 36 #define EXP1_07_PIN 34 #define EXP1_08_PIN 35 #define EXP1_09_PIN 40 #define EXP1_10_PIN 41 #define EXP2_01_PIN 49 #define EXP2_04_PIN 44 #define EXP2_05_PIN 51 #define EXP2_06_PIN 42 #define EXP2_07_PIN 53 #define EXP2_08_PIN 43 #define EXP2_09_PIN 52 #define EXP2_10_PIN 50 #if ENABLED(CR10_STOCKDISPLAY) #define EXP3_03_PIN EXP1_03_PIN #define EXP3_04_PIN EXP1_04_PIN #define EXP3_05_PIN EXP1_05_PIN #define EXP3_06_PIN EXP1_06_PIN #define EXP3_07_PIN EXP1_07_PIN #define EXP3_08_PIN EXP1_08_PIN #define EXP3_09_PIN EXP1_09_PIN #define EXP3_10_PIN EXP1_10_PIN #endif /************************************/ /***** Configurations Section ******/ /************************************/ /** * This section starts with the pins_RAMPS_144.h as example, after if you need any new * display, you could use normal duponts and connect it with with the scheme showed before. * Tested: * - Ender 3 Old display (Character LCD) * - Ender 3 New Serial DWING Display * - Reprap Display * - Ender 5 New Serial Display * - Any Reprap character display like */ #if HAS_WIRED_LCD // // LCD Display output pins // #if HAS_DWIN_E3V2 || IS_DWIN_MARLINUI #if LCD_SERIAL_PORT != 1 #error "LCD_SERIAL_PORT should be 1 for this display." #endif // DWIN Encoder #define BTN_ENC EXP1_09_PIN #define BTN_EN1 EXP1_08_PIN #define BTN_EN2 EXP1_07_PIN #ifndef BEEPER_PIN #define BEEPER_PIN EXP1_10_PIN #undef SPEAKER #endif #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) // TO TEST //#define LCD_PINS_RS EXP2_01_PIN // CS chip select /SS chip slave select //#define LCD_PINS_ENABLE EXP2_05_PIN // SID (MOSI) //#define LCD_PINS_D4 EXP2_09_PIN // SCK (CLK) clock #elif BOTH(IS_NEWPANEL, PANEL_ONE) // TO TEST //#define LCD_PINS_RS EXP1_09_PIN //#define LCD_PINS_ENABLE EXP2_06_PIN //#define LCD_PINS_D4 57 // Mega/Due:65 - AGCM4:57 //#define LCD_PINS_D5 58 // Mega/Due:66 - AGCM4:58 //#define LCD_PINS_D6 EXP2_04_PIN //#define LCD_PINS_D7 56 // Mega/Due:64 - AGCM4:56 #else #if ENABLED(CR10_STOCKDISPLAY) // TO TEST #define LCD_PINS_RS EXP3_04_PIN #define LCD_PINS_ENABLE EXP3_03_PIN #define LCD_PINS_D4 EXP3_05_PIN #if !IS_NEWPANEL // TO TEST //#define BEEPER_PIN EXP3_05_PIN #endif #elif ENABLED(ZONESTAR_LCD) // TO TEST //#define LCD_PINS_RS 56 // Mega/Due:64 - AGCM4:56 //#define LCD_PINS_ENABLE EXP2_04_PIN //#define LCD_PINS_D4 55 // Mega/Due:63 - AGCM4:55 //#define LCD_PINS_D5 EXP1_09_PIN //#define LCD_PINS_D6 EXP2_06_PIN //#define LCD_PINS_D7 57 // Mega/Due:65 - AGCM4:57 #else #if EITHER(MKS_12864OLED, MKS_12864OLED_SSD1306) // TO TEST //#define LCD_PINS_DC 25 // Set as output on init //#define LCD_PINS_RS 27 // Pull low for 1s to init // DOGM SPI LCD Support //#define DOGLCD_CS 16 //#define DOGLCD_MOSI 17 //#define DOGLCD_SCK 23 //#define DOGLCD_A0 LCD_PINS_DC #else // Definitions for any standard Display #define LCD_PINS_RS EXP1_07_PIN #define LCD_PINS_ENABLE EXP1_08_PIN #define LCD_PINS_D4 EXP1_06_PIN #define LCD_PINS_D5 EXP1_05_PIN #define LCD_PINS_D6 EXP1_04_PIN #endif #define LCD_PINS_D7 EXP1_03_PIN #if !IS_NEWPANEL #define BEEPER_PIN EXP1_10_PIN #endif #endif #if !IS_NEWPANEL // Buttons attached to a shift register // Not wired yet //#define SHIFT_CLK_PIN EXP1_04_PIN //#define SHIFT_LD_PIN EXP2_06_PIN //#define SHIFT_OUT_PIN EXP1_09_PIN //#define SHIFT_EN_PIN 17 #endif #endif // // LCD Display input pins // #if IS_NEWPANEL #if IS_RRD_SC #define BEEPER_PIN EXP1_10_PIN #if ENABLED(CR10_STOCKDISPLAY) // TO TEST #define BTN_EN1 EXP3_08_PIN #define BTN_EN2 EXP3_06_PIN #else // Definitions for any standard Display #define BTN_EN1 EXP2_06_PIN #define BTN_EN2 EXP2_08_PIN #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder #endif #endif #define BTN_ENC EXP1_09_PIN #ifndef SD_DETECT_PIN #define SD_DETECT_PIN EXP2_04_PIN #endif #define KILL_PIN EXP2_01_PIN #if ENABLED(BQ_LCD_SMART_CONTROLLER) //#define LCD_BACKLIGHT_PIN EXP1_03_PIN // TO TEST #endif #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) // TO TEST //#define BTN_EN1 56 // Mega/Due:64 - AGCM4:56 //#define BTN_EN2 72 // Mega/Due:59 - AGCM4:72 //#define BTN_ENC 55 //#define SD_DETECT_PIN EXP2_06_PIN #elif ENABLED(LCD_I2C_PANELOLU2) // TO TEST //#define BTN_EN1 47 //#define BTN_EN2 EXP2_08_PIN //#define BTN_ENC 32 //#define LCD_SDSS SDSS //#define KILL_PIN EXP1_10_PIN #elif ENABLED(LCD_I2C_VIKI) // TO TEST //#define BTN_EN1 EXP1_09_PIN // https://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42. //#define BTN_EN2 EXP2_06_PIN //#define BTN_ENC -1 //#define LCD_SDSS SDSS //#define SD_DETECT_PIN EXP2_01_PIN #elif ANY(VIKI2, miniVIKI) // TO TEST //#define DOGLCD_CS 45 //#define DOGLCD_A0 EXP2_04_PIN //#define LCD_SCREEN_ROT_180 //#define BEEPER_PIN 33 //#define STAT_LED_RED_PIN 32 //#define STAT_LED_BLUE_PIN EXP1_08_PIN //#define BTN_EN1 22 //#define BTN_EN2 7 //#define BTN_ENC EXP1_03_PIN //#define SD_DETECT_PIN -1 // Pin 49 for display SD interface, 72 for easy adapter board //#define KILL_PIN 31 #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) // TO TEST //#define DOGLCD_CS 29 //#define DOGLCD_A0 27 //#define BEEPER_PIN 23 //#define LCD_BACKLIGHT_PIN 33 //#define BTN_EN1 EXP1_08_PIN //#define BTN_EN2 EXP1_05_PIN //#define BTN_ENC 31 //#define LCD_SDSS SDSS //#define SD_DETECT_PIN EXP2_01_PIN //#define KILL_PIN EXP1_10_PIN #elif EITHER(MKS_MINI_12864, FYSETC_MINI_12864) // TO TEST //#define BEEPER_PIN EXP1_05_PIN //#define BTN_ENC EXP1_08_PIN //#define SD_DETECT_PIN EXP2_01_PIN //#ifndef KILL_PIN // #define KILL_PIN EXP1_10_PIN //#endif #if ENABLED(MKS_MINI_12864) // TO TEST //#define DOGLCD_A0 27 //#define DOGLCD_CS 25 // GLCD features // Uncomment screen orientation //#define LCD_SCREEN_ROT_90 //#define LCD_SCREEN_ROT_180 //#define LCD_SCREEN_ROT_270 // not connected to a pin //#define LCD_BACKLIGHT_PIN 57 // backlight LED on A11/D? (Mega/Due:65 - AGCM4:57) //#define BTN_EN1 31 //#define BTN_EN2 33 #elif ENABLED(FYSETC_MINI_12864) // From https://wiki.fysetc.com/Mini12864_Panel/ // TO TEST //#define DOGLCD_A0 16 //#define DOGLCD_CS 17 //#define BTN_EN1 33 //#define BTN_EN2 31 //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems // results in LCD soft SPI mode 3, SD soft SPI mode 0 //#define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally. #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) #ifndef RGB_LED_R_PIN // TO TEST //#define RGB_LED_R_PIN 25 #endif #ifndef RGB_LED_G_PIN // TO TEST //#define RGB_LED_G_PIN 27 #endif #ifndef RGB_LED_B_PIN // TO TEST //#define RGB_LED_B_PIN 29 #endif #elif ENABLED(FYSETC_MINI_12864_2_1) // TO TEST //#define NEOPIXEL_PIN 25 #endif #endif #elif ENABLED(MINIPANEL) // TO TEST //#define BEEPER_PIN EXP2_06_PIN // not connected to a pin //#define LCD_BACKLIGHT_PIN 57 // backlight LED on A11/D? (Mega/Due:65 - AGCM4:57) //#define DOGLCD_A0 EXP2_04_PIN //#define DOGLCD_CS 58 // Mega/Due:66 - AGCM4:58 // GLCD features // Uncomment screen orientation //#define LCD_SCREEN_ROT_90 //#define LCD_SCREEN_ROT_180 //#define LCD_SCREEN_ROT_270 //#define BTN_EN1 EXP1_09_PIN //#define BTN_EN2 55 // Mega/Due:63 - AGCM4:55 //#define BTN_ENC 72 // Mega/Due:59 - AGCM4:72 //#define SD_DETECT_PIN EXP2_01_PIN //#define KILL_PIN 56 // Mega/Due:64 - AGCM4:56 #elif ENABLED(ZONESTAR_LCD) // TO TEST //#define ADC_KEYPAD_PIN 12 #elif ENABLED(AZSMZ_12864) // TO TEST #else // Beeper on AUX-4 //#define BEEPER_PIN 33 // Buttons are directly attached to AUX-2 #if IS_RRW_KEYPAD // TO TEST //#define SHIFT_OUT_PIN EXP1_09_PIN //#define SHIFT_CLK_PIN EXP2_04_PIN //#define SHIFT_LD_PIN EXP2_06_PIN //#define BTN_EN1 56 // Mega/Due:64 - AGCM4:56 //#define BTN_EN2 72 // Mega/Due:59 - AGCM4:72 //#define BTN_ENC 55 // Mega/Due:63 - AGCM4:55 #elif ENABLED(PANEL_ONE) // TO TEST //#define BTN_EN1 72 // AUX2 PIN 3 (Mega/Due:59 - AGCM4:72) //#define BTN_EN2 55 // AUX2 PIN 4 (Mega/Due:63 - AGCM4:55) //#define BTN_ENC EXP2_01_PIN // AUX3 PIN 7 #else // TO TEST //#define BTN_EN1 EXP1_05_PIN //#define BTN_EN2 EXP1_08_PIN //#define BTN_ENC 31 #endif #if ENABLED(G3D_PANEL) // TO TEST //#define SD_DETECT_PIN EXP2_01_PIN //#define KILL_PIN EXP1_10_PIN #endif #endif #endif // IS_NEWPANEL #endif // HAS_WIRED_LCD // // SD Support // /** * Bricolemon has an SD slot, but to change it to your LCD or Custom, set the option to one of the following: * * LCD - Use the SD drive in the external LCD controller. * ONBOARD - Use the SD drive on the control board. * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). * * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] */ #ifndef SDCARD_CONNECTION #define SDCARD_CONNECTION ONBOARD #endif #if SD_CONNECTION_IS(ONBOARD) #define SDSS 83 #undef SD_DETECT_PIN #define SD_DETECT_PIN 95 #else #define SDSS EXP2_07_PIN #endif #if HAS_TMC_UART /** * Address for the UART Configuration of the TMC2209. Override in Configuration files. * To test TMC2209 Steppers enable TMC_DEBUG in Configuration_adv.h and test the M122 command with voltage on the steppers. */ #ifndef X_SLAVE_ADDRESS #define X_SLAVE_ADDRESS 0b00 #endif #ifndef Y_SLAVE_ADDRESS #define Y_SLAVE_ADDRESS 0b01 #endif #ifndef Z_SLAVE_ADDRESS #define Z_SLAVE_ADDRESS 0b10 #endif #ifndef E0_SLAVE_ADDRESS #define E0_SLAVE_ADDRESS 0b11 #endif /** * TMC2208/TMC2209 stepper drivers * It seems to work perfectly fine on Software Serial, if an advanced user wants to test, you could use the SAMD51 Serial1 and Serial 2. Be careful with the Sercom configurations. */ //#define X_HARDWARE_SERIAL Serial1 //#define Y_HARDWARE_SERIAL Serial1 //#define Z_HARDWARE_SERIAL Serial1 //#define E0_HARDWARE_SERIAL Serial1 // This is the stable default value after testing, but, higher UART rates could be configured, remeber to test the Steppers with the M122 command to check if everything works. #define TMC_BAUD_RATE 250000 // // Software serial // #define X_SERIAL_TX_PIN 0 #define X_SERIAL_RX_PIN 1 #define Y_SERIAL_TX_PIN X_SERIAL_TX_PIN #define Y_SERIAL_RX_PIN X_SERIAL_RX_PIN #define Z_SERIAL_TX_PIN X_SERIAL_TX_PIN #define Z_SERIAL_RX_PIN X_SERIAL_RX_PIN #define E0_SERIAL_TX_PIN X_SERIAL_TX_PIN #define E0_SERIAL_RX_PIN X_SERIAL_RX_PIN #endif