/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once /** * RAMPS-FD * * No EEPROM * Use 4k7 thermistor tables */ #include "env_validate.h" #ifndef BOARD_INFO_NAME #define BOARD_INFO_NAME "RAMPS-FD v1" #endif #define INVERTED_HEATER_PINS #define INVERTED_BED_PINS #define INVERTED_FAN_PINS // // Servos // #define SERVO0_PIN 7 #define SERVO1_PIN 6 #define SERVO2_PIN 5 #define SERVO3_PIN 3 // // Limit Switches // #define X_MIN_PIN 22 #define X_MAX_PIN 30 #define Y_MIN_PIN 24 #define Y_MAX_PIN 38 #define Z_MIN_PIN 26 #define Z_MAX_PIN 34 // // Steppers // #define X_STEP_PIN 63 #define X_DIR_PIN 62 #define X_ENABLE_PIN 48 #ifndef X_CS_PIN #define X_CS_PIN 68 #endif #define Y_STEP_PIN 65 #define Y_DIR_PIN 64 #define Y_ENABLE_PIN 46 #ifndef Y_CS_PIN #define Y_CS_PIN 60 #endif #define Z_STEP_PIN 67 #define Z_DIR_PIN 66 #define Z_ENABLE_PIN 44 #ifndef Z_CS_PIN #define Z_CS_PIN 58 #endif #define E0_STEP_PIN 36 #define E0_DIR_PIN 28 #define E0_ENABLE_PIN 42 #ifndef E0_CS_PIN #define E0_CS_PIN 67 #endif #define E1_STEP_PIN 43 #define E1_DIR_PIN 41 #define E1_ENABLE_PIN 39 #ifndef E1_CS_PIN #define E1_CS_PIN 61 #endif #define E2_STEP_PIN 32 #define E2_DIR_PIN 47 #define E2_ENABLE_PIN 45 #ifndef E2_CS_PIN #define E2_CS_PIN 59 #endif // // Temperature Sensors // #define TEMP_0_PIN 1 // Analog Input #define TEMP_1_PIN 2 // Analog Input #define TEMP_2_PIN 3 // Analog Input #define TEMP_BED_PIN 0 // Analog Input // SPI for MAX Thermocouple #if DISABLED(SDSUPPORT) #define TEMP_0_CS_PIN 53 #else #define TEMP_0_CS_PIN 49 #endif // // Heaters / Fans // #define HEATER_0_PIN 9 #define HEATER_1_PIN 10 #define HEATER_2_PIN 11 #define HEATER_BED_PIN 8 #ifndef FAN_PIN #define FAN_PIN 12 #endif // // Misc. Functions // #define SDSS 4 #define LED_PIN 13 /** ------ ------ * 37 |10 9 | 35 (MISO) 50 |10 9 | 76 (SCK) * 29 | 8 7 | 27 (EN2) 31 | 8 7 | 4 (SD_SS) * 25 6 5 | 23 (EN1) 33 6 5 | 75 (MOSI) * 16 | 4 3 | 17 (SDD) 49 | 4 3 | RESET * GND | 2 1 | 5V GND | 2 1 | -- * ------ ------ * EXP1 EXP2 */ #define EXP1_03_PIN 17 #define EXP1_04_PIN 16 #define EXP1_05_PIN 23 #define EXP1_06_PIN 25 #define EXP1_07_PIN 27 #define EXP1_08_PIN 29 #define EXP1_09_PIN 35 #define EXP1_10_PIN 37 #define EXP2_03_PIN -1 #define EXP2_04_PIN 49 #define EXP2_05_PIN 75 #define EXP2_06_PIN 33 #define EXP2_07_PIN 4 #define EXP2_08_PIN 31 #define EXP2_09_PIN 76 #define EXP2_10_PIN 74 // // LCD / Controller // #if HAS_WIRED_LCD // ramps-fd lcd adaptor #define BEEPER_PIN EXP1_10_PIN #define BTN_EN1 EXP2_06_PIN #define BTN_EN2 EXP2_08_PIN #define BTN_ENC EXP1_09_PIN #define SD_DETECT_PIN EXP2_04_PIN #if IS_NEWPANEL #define LCD_PINS_RS EXP1_04_PIN #define LCD_PINS_ENABLE EXP1_03_PIN #endif #if ENABLED(FYSETC_MINI_12864) #define DOGLCD_CS LCD_PINS_ENABLE #define DOGLCD_A0 LCD_PINS_RS #define DOGLCD_SCK EXP2_09_PIN #define DOGLCD_MOSI EXP2_05_PIN //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems // results in LCD soft SPI mode 3, SD soft SPI mode 0 #define LCD_RESET_PIN EXP1_05_PIN // Must be high or open for LCD to operate normally. #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) #ifndef RGB_LED_R_PIN #define RGB_LED_R_PIN EXP1_06_PIN #endif #ifndef RGB_LED_G_PIN #define RGB_LED_G_PIN EXP1_07_PIN #endif #ifndef RGB_LED_B_PIN #define RGB_LED_B_PIN EXP1_08_PIN #endif #elif ENABLED(FYSETC_MINI_12864_2_1) #define NEOPIXEL_PIN EXP1_06_PIN #endif #elif IS_NEWPANEL #define LCD_PINS_D4 EXP1_05_PIN #define LCD_PINS_D5 EXP1_06_PIN #define LCD_PINS_D6 EXP1_07_PIN #define LCD_PINS_D7 EXP1_08_PIN #if ENABLED(MINIPANEL) #define DOGLCD_CS EXP1_06_PIN #define DOGLCD_A0 EXP1_07_PIN #endif #endif #if ANY(VIKI2, miniVIKI) #define DOGLCD_A0 EXP1_04_PIN #define KILL_PIN 51 #define STAT_LED_BLUE_PIN EXP1_08_PIN #define STAT_LED_RED_PIN EXP1_05_PIN #define DOGLCD_CS EXP1_03_PIN #define DOGLCD_SCK EXP2_09_PIN // SCK_PIN - Required for DUE Hardware SPI #define DOGLCD_MOSI EXP2_05_PIN // MOSI_PIN #define DOGLCD_MISO EXP2_10_PIN // MISO_PIN #endif #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder #endif #endif // HAS_WIRED_LCD #if HAS_TMC_UART /** * TMC2208/TMC2209 stepper drivers * * Hardware serial communication ports. * If undefined software serial is used according to the pins below */ //#define X_HARDWARE_SERIAL Serial1 //#define X2_HARDWARE_SERIAL Serial1 //#define Y_HARDWARE_SERIAL Serial1 //#define Y2_HARDWARE_SERIAL Serial1 //#define Z_HARDWARE_SERIAL Serial1 //#define Z2_HARDWARE_SERIAL Serial1 //#define E0_HARDWARE_SERIAL Serial1 //#define E1_HARDWARE_SERIAL Serial1 //#define E2_HARDWARE_SERIAL Serial1 //#define E3_HARDWARE_SERIAL Serial1 //#define E4_HARDWARE_SERIAL Serial1 #endif // // M3/M4/M5 - Spindle/Laser Control // #if HOTENDS < 3 && HAS_CUTTER && !PIN_EXISTS(SPINDLE_LASER_ENA) #define SPINDLE_LASER_ENA_PIN 45 // Use E2 ENA #define SPINDLE_LASER_PWM_PIN 12 // Hardware PWM #define SPINDLE_DIR_PIN 47 // Use E2 DIR #endif