/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once /** * Z-Bolt X Series board – based on Arduino Mega2560 */ #define REQUIRE_MEGA2560 #include "env_validate.h" #if HOTENDS > 4 || E_STEPPERS > 4 #error "Z-Bolt X Series board supports up to 4 hotends / E-steppers." #endif #define BOARD_INFO_NAME "Z-Bolt X Series" // // Servos // #ifndef SERVO0_PIN #define SERVO0_PIN 11 #endif #ifndef SERVO3_PIN #define SERVO3_PIN 4 #endif // // Limit Switches // #define X_MIN_PIN 3 #ifndef X_MAX_PIN #define X_MAX_PIN 2 #endif #define Y_MIN_PIN 14 #define Y_MAX_PIN 15 #define Z_MIN_PIN 18 #define Z_MAX_PIN 19 // // Z Probe (when not Z_MIN_PIN) // #ifndef Z_MIN_PROBE_PIN #define Z_MIN_PROBE_PIN 32 #endif // // Steppers // #define X_STEP_PIN 54 #define X_DIR_PIN 55 #define X_ENABLE_PIN 38 #ifndef X_CS_PIN #define X_CS_PIN -1 #endif #define Y_STEP_PIN 60 #define Y_DIR_PIN 61 #define Y_ENABLE_PIN 56 #ifndef Y_CS_PIN #define Y_CS_PIN -1 #endif #define Z_STEP_PIN 46 #define Z_DIR_PIN 48 #define Z_ENABLE_PIN 62 #ifndef Z_CS_PIN #define Z_CS_PIN -1 #endif #define E0_STEP_PIN 26 #define E0_DIR_PIN 28 #define E0_ENABLE_PIN 24 #ifndef E0_CS_PIN #define E0_CS_PIN -1 #endif #define E1_STEP_PIN 36 #define E1_DIR_PIN 34 #define E1_ENABLE_PIN 30 #ifndef E1_CS_PIN #define E1_CS_PIN -1 #endif // Red #define E2_STEP_PIN 42 #define E2_DIR_PIN 40 #define E2_ENABLE_PIN 65 #ifndef E2_CS_PIN #define E2_CS_PIN -1 #endif // Black #define E3_STEP_PIN 44 #define E3_DIR_PIN 64 #define E3_ENABLE_PIN 66 #ifndef E3_CS_PIN #define E3_CS_PIN -1 #endif // // Temperature Sensors // #define TEMP_0_PIN 13 // Analog Input #define TEMP_1_PIN 15 // Analog Input #define TEMP_2_PIN 5 // Analog Input (BLACK) #define TEMP_3_PIN 9 // Analog Input (RED) #define TEMP_BED_PIN 14 // Analog Input // // Heaters / Fans // #define HEATER_0_PIN 10 #define HEATER_1_PIN 7 #define HEATER_2_PIN 6 #define HEATER_3_PIN 5 #define HEATER_BED_PIN 8 #define FAN_PIN 9 // // Misc. Functions // #define SDSS 53 #define LED_PIN 13 #ifndef FILWIDTH_PIN #define FILWIDTH_PIN 5 // Analog Input on AUX2 #endif // Оn the servos connector #ifndef FIL_RUNOUT_PIN #define FIL_RUNOUT_PIN 4 #endif #ifndef PS_ON_PIN #define PS_ON_PIN 12 #endif #if ENABLED(CASE_LIGHT_ENABLE) && !defined(CASE_LIGHT_PIN) && !defined(SPINDLE_LASER_ENA_PIN) #if NUM_SERVOS <= 1 // Prefer the servo connector #define CASE_LIGHT_PIN 6 // Hardware PWM #elif HAS_FREE_AUX2_PINS #define CASE_LIGHT_PIN 44 // Hardware PWM #endif #endif // // M3/M4/M5 - Spindle/Laser Control // #if HAS_CUTTER && !PIN_EXISTS(SPINDLE_LASER_ENA) #if !defined(NUM_SERVOS) || NUM_SERVOS == 0 // Prefer the servo connector #define SPINDLE_LASER_ENA_PIN 4 // Pullup or pulldown! #define SPINDLE_LASER_PWM_PIN 6 // Hardware PWM #define SPINDLE_DIR_PIN 5 #elif HAS_FREE_AUX2_PINS #define SPINDLE_LASER_ENA_PIN 40 // Pullup or pulldown! #define SPINDLE_LASER_PWM_PIN 44 // Hardware PWM #define SPINDLE_DIR_PIN 65 #endif #endif // // TMC software SPI // #if ENABLED(TMC_USE_SW_SPI) #ifndef TMC_SW_MOSI #define TMC_SW_MOSI 66 #endif #ifndef TMC_SW_MISO #define TMC_SW_MISO 44 #endif #ifndef TMC_SW_SCK #define TMC_SW_SCK 64 #endif #endif #if HAS_TMC_UART /** * TMC220x stepper drivers * * Hardware serial communication ports. * If undefined software serial is used according to the pins below */ //#define X_HARDWARE_SERIAL Serial1 //#define X2_HARDWARE_SERIAL Serial1 //#define Y_HARDWARE_SERIAL Serial1 //#define Y2_HARDWARE_SERIAL Serial1 //#define Z_HARDWARE_SERIAL Serial1 //#define Z2_HARDWARE_SERIAL Serial1 //#define E0_HARDWARE_SERIAL Serial1 //#define E1_HARDWARE_SERIAL Serial1 //#define E2_HARDWARE_SERIAL Serial1 //#define E3_HARDWARE_SERIAL Serial1 //#define E4_HARDWARE_SERIAL Serial1 #ifndef X_SERIAL_TX_PIN #define X_SERIAL_TX_PIN 40 #endif #ifndef X_SERIAL_RX_PIN #define X_SERIAL_RX_PIN 63 #endif #ifndef X2_SERIAL_TX_PIN #define X2_SERIAL_TX_PIN -1 #endif #ifndef X2_SERIAL_RX_PIN #define X2_SERIAL_RX_PIN -1 #endif #ifndef Y_SERIAL_TX_PIN #define Y_SERIAL_TX_PIN 59 #endif #ifndef Y_SERIAL_RX_PIN #define Y_SERIAL_RX_PIN 64 #endif #ifndef Y2_SERIAL_TX_PIN #define Y2_SERIAL_TX_PIN -1 #endif #ifndef Y2_SERIAL_RX_PIN #define Y2_SERIAL_RX_PIN -1 #endif #ifndef Z_SERIAL_TX_PIN #define Z_SERIAL_TX_PIN 42 #endif #ifndef Z_SERIAL_RX_PIN #define Z_SERIAL_RX_PIN 65 #endif #ifndef Z2_SERIAL_TX_PIN #define Z2_SERIAL_TX_PIN -1 #endif #ifndef Z2_SERIAL_RX_PIN #define Z2_SERIAL_RX_PIN -1 #endif #ifndef E0_SERIAL_TX_PIN #define E0_SERIAL_TX_PIN 44 #endif #ifndef E0_SERIAL_RX_PIN #define E0_SERIAL_RX_PIN 66 #endif #ifndef E1_SERIAL_TX_PIN #define E1_SERIAL_TX_PIN -1 #endif #ifndef E1_SERIAL_RX_PIN #define E1_SERIAL_RX_PIN -1 #endif #ifndef E2_SERIAL_TX_PIN #define E2_SERIAL_TX_PIN -1 #endif #ifndef E2_SERIAL_RX_PIN #define E2_SERIAL_RX_PIN -1 #endif #ifndef E3_SERIAL_TX_PIN #define E3_SERIAL_TX_PIN -1 #endif #ifndef E3_SERIAL_RX_PIN #define E3_SERIAL_RX_PIN -1 #endif #ifndef E4_SERIAL_TX_PIN #define E4_SERIAL_TX_PIN -1 #endif #ifndef E4_SERIAL_RX_PIN #define E4_SERIAL_RX_PIN -1 #endif #ifndef E5_SERIAL_TX_PIN #define E5_SERIAL_TX_PIN -1 #endif #ifndef E5_SERIAL_RX_PIN #define E5_SERIAL_RX_PIN -1 #endif #ifndef E6_SERIAL_TX_PIN #define E6_SERIAL_TX_PIN -1 #endif #ifndef E6_SERIAL_RX_PIN #define E6_SERIAL_RX_PIN -1 #endif #ifndef E7_SERIAL_TX_PIN #define E7_SERIAL_TX_PIN -1 #endif #ifndef E7_SERIAL_RX_PIN #define E7_SERIAL_RX_PIN -1 #endif #endif