/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ #pragma once /** * BigTreeTech SKR 1.1 pin assignments */ #define BOARD_INFO_NAME "BTT SKR V1.1" // // Limit Switches // #define X_MIN_PIN P1_29 #define X_MAX_PIN P1_28 #define Y_MIN_PIN P1_27 #define Y_MAX_PIN P1_26 #define Z_MIN_PIN P1_25 #define Z_MAX_PIN P1_24 // // Steppers // #define X_STEP_PIN P0_04 #define X_DIR_PIN P0_05 #define X_ENABLE_PIN P4_28 #define Y_STEP_PIN P2_01 #define Y_DIR_PIN P2_02 #define Y_ENABLE_PIN P2_00 #define Z_STEP_PIN P0_20 #define Z_DIR_PIN P0_21 #define Z_ENABLE_PIN P0_19 #define E0_STEP_PIN P0_11 #define E0_DIR_PIN P2_13 #define E0_ENABLE_PIN P2_12 /** ------ ------ * 1.30 |10 9 | 2.11 0.17 |10 9 | 0.15 * 0.18 | 8 7 | 0.16 3.26 | 8 7 | 1.23 * 0.15 6 5 | -- 3.25 6 5 | 0.18 * -- | 4 3 | -- 1.31 | 4 3 | RESET * GND | 2 1 | 5V GND | 2 1 | -- * ------ ------ * EXP1 EXP2 */ #define EXP1_03_PIN -1 // NC #define EXP1_04_PIN -1 // NC #define EXP1_05_PIN -1 // NC #define EXP1_06_PIN P0_15 #define EXP1_07_PIN P0_16 #define EXP1_08_PIN P0_18 #define EXP1_09_PIN P2_11 #define EXP1_10_PIN P1_30 #define EXP2_03_PIN -1 // RESET #define EXP2_04_PIN P1_31 #define EXP2_05_PIN P0_18 #define EXP2_06_PIN P3_25 #define EXP2_07_PIN P1_23 #define EXP2_08_PIN P3_26 #define EXP2_09_PIN P0_15 #define EXP2_10_PIN P0_17 /** * LCD / Controller * * As of 20 JAN 2019 only the REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER display has * been tested with these settings. It can be connected to the SKR using standard cables * via the EXP1 and EXP2 ports. Other displays may need a custom cable and/or changes to * the pins defined below. * * The SD card on the LCD controller uses the same SPI signals as the LCD, resulting in * garbage/lines on the LCD display during SD card access. The LCD code mitigates this * by redrawing the screen after SD card accesses. */ #if IS_TFTGLCD_PANEL #if ENABLED(TFTGLCD_PANEL_SPI) #define TFTGLCD_CS EXP2_08_PIN #endif #elif HAS_WIRED_LCD #define BTN_EN1 EXP2_08_PIN #define BTN_EN2 EXP2_06_PIN #define BTN_ENC EXP1_09_PIN #define LCD_SDSS EXP2_07_PIN #define LCD_PINS_RS EXP1_07_PIN #define LCD_PINS_ENABLE EXP2_05_PIN #define LCD_PINS_D4 EXP2_09_PIN #if ENABLED(MKS_MINI_12864) #define DOGLCD_CS P2_06 #define DOGLCD_A0 EXP1_07_PIN #endif #endif // HAS_WIRED_LCD // // SD Support // // MKS_MINI_12864 strongly prefers the SD card on the display and // requires jumpers on the SKR V1.1 board as documented here: // https://www.facebook.com/groups/505736576548648/permalink/630639874058317/ #ifndef SDCARD_CONNECTION #if ANY(MKS_MINI_12864, ENDER2_STOCKDISPLAY, IS_TFTGLCD_PANEL) #define SDCARD_CONNECTION LCD #else #define SDCARD_CONNECTION ONBOARD #endif #endif // Trinamic driver support #if HAS_TRINAMIC_CONFIG // Using TMC devices in intelligent mode requires extra connections to each device. Unfortunately // the SKR does not have many free pins (especially if a display is in use). The SPI-based devices // will require 3 connections (clock, mosi, miso), plus a chip select line (CS) for each driver. // The UART-based devices require 2 pis per driver (one of which must be interrupt capable). // The same SPI pins can be shared with the display/SD card reader, meaning SPI-based devices are // probably a good choice for this board. // // SOFTWARE_DRIVER_ENABLE is a good option. It uses SPI to control the driver enable and allows the // hardware ENABLE pins for each driver to be repurposed as SPI chip select. To use this mode the // driver modules will probably need to be modified, removing the pin used for the enable line from // the module and wiring this connection directly to GND (as is the case for TMC2130). // Using this option and sharing all of the SPI pins allows 5 TMC2130 drivers to be used along with // a REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER without requiring the use of any extra pins. // // Other options will probably require the use of any free pins and the TFT serial port or a // different type of display (like the TFT), using the pins normally used for the display and encoder. // Unfortunately, tests show it's not possible to use endstop and thermistor pins for chip-select. // Sample settings are provided below, but only some have been tested. // // Another option is to share the enable and chip-select pins when using SPI. Several users have // reported that this works. However, it's unlikely that this configuration will allow SPI communi- // cation with the device when the drivers are active, meaning that some of the more advanced TMC // options may not be available. // When using any TMC SPI-based drivers, software SPI is used // because pins may be shared with the display or SD card. #define TMC_USE_SW_SPI #define TMC_SW_MOSI EXP2_05_PIN #define TMC_SW_MISO EXP2_10_PIN // To minimize pin usage use the same clock pin as the display/SD card reader. (May generate LCD noise.) #define TMC_SW_SCK EXP2_09_PIN // If pin 2_06 is unused, it can be used for the clock to avoid the LCD noise. //#define TMC_SW_SCK P2_06 #if ENABLED(SOFTWARE_DRIVER_ENABLE) // Software enable allows the enable pins to be repurposed as chip-select pins. // Note: Requires the driver modules to be modified to always be enabled with the enable pin removed. #if AXIS_DRIVER_TYPE_X(TMC2130) #define X_CS_PIN P4_28 #undef X_ENABLE_PIN #endif #if AXIS_DRIVER_TYPE_Y(TMC2130) #define Y_CS_PIN P2_00 #undef Y_ENABLE_PIN #endif #if AXIS_DRIVER_TYPE_Z(TMC2130) #define Z_CS_PIN P0_19 #undef Z_ENABLE_PIN #endif #if AXIS_DRIVER_TYPE_E0(TMC2130) #define E0_CS_PIN P2_12 #undef E0_ENABLE_PIN #endif #if AXIS_DRIVER_TYPE_E1(TMC2130) #define E1_CS_PIN P0_10 #undef E1_ENABLE_PIN #endif #else // !SOFTWARE_DRIVER_ENABLE // A chip-select pin is needed for each driver. // EXAMPLES // Example 1: No LCD attached or a TFT style display using the AUX header RX/TX pins. // SDCARD_CONNECTION must not be 'LCD'. Nothing should be connected to EXP1/EXP2. //#define SKR_USE_LCD_PINS_FOR_CS #if ENABLED(SKR_USE_LCD_PINS_FOR_CS) #define X_CS_PIN EXP2_07_PIN #define Y_CS_PIN EXP2_08_PIN #define Z_CS_PIN EXP1_09_PIN #define E0_CS_PIN EXP2_06_PIN #define E1_CS_PIN EXP2_04_PIN #endif // Example 2: A REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER // The SD card reader attached to the LCD (if present) can't be used because // the pins will be in use. So SDCARD_CONNECTION must not be 'LCD'. //#define SKR_USE_LCD_SD_CARD_PINS_FOR_CS #if ENABLED(SKR_USE_LCD_SD_CARD_PINS_FOR_CS) #define X_CS_PIN P0_02 #define Y_CS_PIN P0_03 #define Z_CS_PIN P2_06 // We use SD_DETECT_PIN for E0 #undef SD_DETECT_PIN #define E0_CS_PIN EXP2_04_PIN // We use LCD_SDSS pin for E1 #undef LCD_SDSS #define LCD_SDSS -1 #define E1_CS_PIN EXP2_07_PIN #endif // Example 3: Use the driver enable pins for chip-select. // Commands must not be sent to the drivers when enabled. So certain // advanced features (like driver monitoring) will not be available. //#define SKR_USE_ENABLE_CS #if ENABLED(SKR_USE_ENABLE_FOR_CS) #define X_CS_PIN X_ENABLE_PIN #define Y_CS_PIN Y_ENABLE_PIN #define Z_CS_PIN Z_ENABLE_PIN #define E0_CS_PIN E0_ENABLE_PIN #define E1_CS_PIN E1_ENABLE_PIN #endif #endif // SOFTWARE_DRIVER_ENABLE #endif // Include common SKR pins #include "pins_BTT_SKR_common.h"